New Arrivals

The 24 Pin 1mm Pitch 300mm FFC Cable is a flexible flat ribbon cable designed for compatible connections between PCBs, electronic components, displays, control boards and other devices that use an FFC interface.

This 24 pin FFC cable features a 1mm pitch, 300mm length, and same-side contact orientation. The exposed contacts at both ends are positioned on the same side of the cable, making it suitable for compatible connectors that require this specific configuration.

Its flexible, flat construction allows the cable to be routed through narrow spaces inside electronic equipment while providing multiple electrical connections in a single compact cable.

Key Features

• 24-Pin Configuration: Provides 24 electrical contacts for compatible FFC connectors.

• 1mm Pitch: Designed for connectors with 1mm contact spacing.

• 300mm Length: Suitable for applications requiring a longer flexible connection.

• Same-Side Connection: Contacts at both ends are positioned on the same side.

• Flexible Flat Design: Easy to route through compact electronic assemblies.

• Low-Profile Construction: Suitable for space-conscious internal connections.

• Replacement Friendly: Useful for compatible repair and maintenance applications.

Product Specifications

Applications

The 24 Pin 1mm Pitch FFC Cable can be used in compatible:

• Printer assemblies

• Scanner assemblies

• Display and control panels

• PCB-to-PCB connections

• Consumer electronics

• Embedded electronic equipment

• Control boards

• DIY electronics projects

• Electronic repair and replacement applications

What Does Same-Side FFC Mean?

A same-side FFC cable has its exposed conductive contacts positioned on the same side at both ends of the cable.

This orientation is important when replacing an existing flexible flat cable. A cable with contacts on opposite sides may have the same number of pins and pitch but still be incompatible with the original connector arrangement.

Always compare the contact orientation of the replacement cable with the original cable before ordering.

Compatibility Guide

Before purchasing this 24 pin FFC cable, verify the following specifications:

• Pin count: 24 pins

• Pitch: 1mm

• Length: 300mm

• Contact orientation: Same Side

• Cable width: Must match the connector

• Connector type: Must be compatible with the intended FFC/FPC socket

Matching only the pin count is not sufficient. The pitch, cable length, contact orientation, width and connector configuration should all be checked.

Installation Information

Switch off and disconnect the electronic equipment before replacing the FFC cable.

Carefully release the locking mechanism of the FFC connector and remove the existing cable. Insert the replacement cable with the contacts facing the correct direction and secure the connector lock.

Avoid sharply folding, twisting, pulling or creasing the cable, particularly near the exposed contact areas. Improper handling can damage the conductive traces and cause intermittent or complete connection failure.

Package Includes

• 1 × 24 Pin 1mm Pitch 300mm Same Side FFC Ribbon Flexible Flat Cable

Frequently Asked Questions

How many pins does this FFC cable have?

This cable has 24 pins.

What is the pitch of the cable?

The contact pitch is 1mm.

What is the length of this FFC cable?

The cable length is 300mm.

What does same-side connection mean?

Same-side connection means the exposed conductive contacts at both ends are located on the same side of the cable.

Can I use this as a replacement for any 24-pin FFC cable?

No. You should also match the 1mm pitch, 300mm length, contact orientation, cable width and connector configuration.

Can this FFC cable be used in printers?

Yes, it can be used in compatible printer assemblies when the original cable has matching specifications and connector configuration.

Is this cable suitable for PCB-to-PCB connections?

Yes, provided both boards use compatible FFC connectors matching the cable's pin count, pitch and contact orientation.

The VORTEX 9x4.5EAR Drone Propeller is an electric drone propeller designed for compatible drone and multirotor applications requiring a reverse-rotation (CW) propeller. Made from glass fiber nylon, this propeller offers a lightweight and rigid construction suitable for replacement and maintenance applications.

The propeller features a grey finish and is specified for CW (clockwise) rotation. The R designation identifies the reverse-rotation version in this product listing, making rotation direction an important consideration when matching it with your drone's motor configuration.

This listing includes 2 pieces, making it suitable as a replacement set or as spare propellers for compatible drone setups.

Key Features

• Model: 9x4.5EAR
• Brand: VORTEX
• Type: Electric Drone Propeller
• Material: Glass Fiber Nylon
• Colour: Grey
• Rotation: CW / Reverse Rotation
• Quantity: 2 Pieces
• Lightweight glass fiber nylon construction
• Suitable for compatible electric drone applications
• Useful for replacement and maintenance
• Reverse-rotation design for compatible motor positions

Applications

The 9x4.5EAR drone propeller can be used for compatible:

• Electric drones
• Multirotor aircraft
• FPV drone projects
• DIY drone builds
• Drone repair and maintenance
• Replacement propeller requirements

Specifications

Package Contents

• 2 × VORTEX 9x4.5EAR Reverse Rotation CW Drone Propellers

Compatibility & Installation

Before purchasing, compare the product with your existing propeller and verify:

• 9x4.5EAR specification
• Required CW/CCW rotation direction
• Motor and shaft compatibility
• Hub and mounting configuration
• Available propeller clearance
• Drone manufacturer's recommended propeller specification

Important: This is a CW/reverse-rotation propeller. Install it only on a motor position that requires this rotation direction.

Important Note

Do not determine compatibility from the propeller's appearance alone. Always verify the exact propeller designation, rotation direction, mounting configuration, and motor compatibility before installation.

Using an incorrect propeller or rotation direction can affect the drone's propulsion and flight configuration.

FAQs

What is the model of this drone propeller?

The model/designation is 9x4.5EAR.

Is this a CW propeller?

Yes. This listing specifies the propeller as CW (clockwise) / reverse rotation.

What material is it made from?

The propeller is made from glass fiber nylon.

What colour is the propeller?

It is supplied in grey.

How many propellers are included?

The package contains 2 pieces.

Is this a CW and CCW pair?

No. This listing contains 2 CW/reverse-rotation propellers.

Can this propeller be used on any 9x4.5 drone?

No. Compatibility depends on the exact propeller version, rotation direction, motor/shaft, hub configuration, and drone manufacturer's requirements.

The VORTEX 7x6R Drone Propeller is an electric drone propeller designed for compatible drone and multirotor applications requiring a reverse-rotation (CW) propeller. Made from glass fiber nylon, it provides a lightweight and rigid construction for drone replacement and maintenance applications.

This 7x6R drone propeller comes in a grey finish and is specified for CW (clockwise) rotation. The R designation indicates the reverse-rotation version in this product listing, making it important to match the rotation direction with the motor position and propulsion configuration of your drone.

The pack contains 2 pieces, making it suitable for replacement or keeping spare propellers available for compatible drone setups.

Key Features

• Model/Size: 7x6R
• Brand: VORTEX
• Type: Electric Drone Propeller
• Material: Glass Fiber Nylon
• Colour: Grey
• Rotation: CW / Reverse Rotation
• Quantity: 2 Pieces
• Lightweight glass fiber nylon construction
• Designed for compatible electric drone applications
• Suitable for replacement and maintenance

Applications

The 7x6R drone propeller can be used for compatible:

• Electric drones
• Multirotor aircraft
• FPV drone builds
• DIY drone projects
• Drone repair and maintenance
• Replacement propeller requirements

Specifications

Package Contents

• 2 × VORTEX 7x6R Reverse Rotation CW Drone Propellers

Compatibility & Installation

Before purchasing or installing, verify:

• 7x6R propeller specification
• Required CW/CCW rotation direction
• Motor/shaft compatibility
• Hub and mounting configuration
• Propeller clearance
• Compatibility with your drone's propulsion system

Important: Rotation direction is critical when installing drone propellers. The 7x6R is specified as a CW/reverse-rotation propeller, so install it only where your drone's motor configuration requires this direction.

Important Note

Do not select the propeller based only on its appearance or size designation. Always compare the existing propeller and your drone manufacturer's specifications for size, rotation direction, hub configuration, and motor compatibility.

FAQs

What does 7x6R mean?

7x6R is the product's propeller designation, with R referring to the reverse-rotation version in this listing.

Is this a CW propeller?

Yes. This product is specified as a CW (clockwise) reverse-rotation propeller.

What material is this propeller made from?

It is made from glass fiber nylon.

How many propellers are included?

The package contains 2 pieces.

What colour is the propeller?

The propellers are grey.

Can I use this propeller on any 7x6 drone?

No. The propeller must match the drone's required rotation direction, motor/shaft configuration, hub, and overall propulsion specifications.

Is this a CW + CCW pair?

No. This listing contains 2 CW/reverse-rotation propellers. It should not be considered a CW + CCW pair unless specifically stated by the manufacturer.

The VORTEX 8x6E/8x6R Drone Propeller is an electric drone propeller designed for compatible drone and multirotor applications. Constructed from glass fiber nylon, it provides a lightweight and rigid propeller construction suitable for replacement and maintenance requirements.

This 8x6E/8x6R drone propeller comes in a grey finish and is specified for CW (clockwise) rotation. The package contains 2 pieces, making it suitable for replacing damaged or worn propellers where the same size, rotation direction, and mounting configuration are required.

Key Features

• Model/Size: 8x6E / 8x6R
• Brand: VORTEX
• Type: Electric Drone Propeller
• Material: Glass Fiber Nylon
• Colour: Grey
• Rotation: CW (Clockwise)
• Quantity: 2 Pieces
• Lightweight glass fiber nylon construction
• Suitable for compatible drone and multirotor applications
• Useful as a replacement or spare propeller

Applications

The 8x6E/8x6R drone propeller can be used for compatible:

• Electric drones
• Multirotor aircraft
• FPV drone projects
• DIY drone builds
• Replacement propeller requirements
• Drone repair and maintenance

Specifications

Package Contents

• 2 × VORTEX 8x6E/8x6R CW Drone Propellers

Compatibility & Installation

Before purchasing, verify the following with your existing propeller and drone:

• 8x6E or 8x6R designation
• Required rotation direction
• Motor/shaft compatibility
• Hub and mounting configuration
• Propeller clearance and physical dimensions

The CW designation indicates clockwise rotation. Install the propeller only on the motor position specified for CW rotation by your drone's propulsion configuration.

Important Note

The 8x6E/8x6R designation should be matched with the specifications of your existing propeller or drone. Do not assume compatibility based only on the appearance or general propeller size.

FAQs

What material is the VORTEX 8x6E/8x6R propeller made from?

It is made from glass fiber nylon.

What does CW mean?

CW means Clockwise rotation. This propeller is intended for a motor position requiring CW rotation.

How many propellers are included?

The package contains 2 CW propellers.

What colour is this propeller?

The propeller is grey.

Can I use this propeller on any 8x6 drone?

No. Compatibility depends on the exact propeller specification, motor/shaft, hub configuration, rotation direction, and drone setup.

Is this a CW and CCW pair?

No. This listing is specified as CW, with 2 pieces supplied. It should not be treated as a CW + CCW pair unless the manufacturer or product packaging specifically confirms that configuration.

The 35mmS Drone Propeller is a compact replacement propeller designed for compatible small electric drones and micro multirotor applications. It features a 2-blade design and is made from PC (polycarbonate) material.

Available in a clear blue finish, this propeller set includes 4 pairs of CW and CCW propellers, providing both rotation directions required for many multirotor configurations. The listed 1mm specification should be matched with the shaft or mounting requirements of your drone before installation.

With both clockwise and counter-clockwise propellers included, this set can be useful for replacing damaged propellers or keeping spare sets available for compatible mini drone builds.

Key Features

• Model/Size: 35mmS
• Material: PC (Polycarbonate)
• Blade Design: 2 Blade
• Mounting/Shaft Specification: 1mm
• Colour: Clear Blue
• Rotation: CW + CCW
• Quantity: 4 Pairs
• Suitable for compatible mini and micro drone applications
• Includes both rotation directions for multirotor setups

Applications

The 35mmS drone propeller can be used for compatible:

• Mini drones
• Micro drones
• Small multirotor aircraft
• DIY drone projects
• Micro FPV builds
• Replacement propeller requirements

Specifications

Package Contents

• 4 × CW 35mmS Drone Propellers
• 4 × CCW 35mmS Drone Propellers

Total: 8 propellers / 4 pairs

Compatibility & Installation Note

Before installation, verify the propeller diameter, shaft/mounting size, blade orientation, and CW/CCW rotation requirement of your drone.

Install CW and CCW propellers in their corresponding motor positions. Using the wrong rotation direction can affect thrust and flight stability.

The 1mm specification should be checked against your motor shaft or mounting arrangement before ordering.

FAQs

What material are these drone propellers made from?

These propellers are made from PC (polycarbonate).

How many blades does each propeller have?

Each propeller has a 2-blade design.

What colour are these propellers?

They have a clear blue finish.

Does the set include both CW and CCW propellers?

Yes. The set includes 4 pairs of CW + CCW propellers.

How many propellers are included in total?

The package contains 8 propellers, supplied as 4 CW + 4 CCW, making 4 pairs.

What drones are these propellers compatible with?

They are intended for compatible small or micro drones. Always verify the exact propeller size, mounting/shaft specification, and rotation direction required by your drone before purchase.

The VORTEX 6x4E/6x4R Drone Propeller is a replacement propeller designed for compatible electric drone and multirotor applications. Made from glass fiber nylon, these propellers offer a lightweight and rigid construction suitable for regular drone use.

This 6x4E/6x4R drone propeller comes in grey and features a CW (clockwise) rotation direction. The pack includes 2 propellers, making it suitable for replacing damaged or worn propellers where the same size, rotation direction, and mounting configuration are required.

Key Features

• Model/Size: 6x4E / 6x4R
• Brand: VORTEX
• Propeller Type: Electric drone propeller
• Material: Glass fiber nylon
• Colour: Grey
• Rotation: CW (Clockwise)
• Quantity: 2 pieces
• Designed for compatible drone and multirotor setups
• Lightweight construction suitable for electric propulsion systems
• Suitable as a replacement for damaged or worn propellers

Applications

The 6x4E/6x4R drone propeller can be used for:

• Compatible electric drones
• Multirotor aircraft
• FPV drone builds
• DIY drone projects
• Replacement of damaged drone propellers
• Spare propeller requirements for compatible models

Important Compatibility Note

Before purchasing, verify the following against your existing propeller:

• 6x4E or 6x4R designation
• Propeller size and profile
• CW rotation direction
• Motor/shaft mounting compatibility
• Propeller hub and mounting-hole configuration

Do not select a propeller based only on appearance. The correct size, rotation direction, hub configuration, and motor compatibility are important for safe and proper drone operation.

Specifications

Package Contents

• 2 × VORTEX 6x4E/6x4R CW Drone Propellers

FAQs

Is this propeller for electric drones?

Yes. It is an electric drone propeller intended for compatible drone and multirotor applications.

What does CW mean on a drone propeller?

CW means Clockwise rotation. The propeller should be installed on a motor position that requires clockwise rotation.

What material is the propeller made from?

The propeller is made from glass fiber nylon.

How many propellers are included?

The package contains 2 pieces of grey CW propellers.

Can I use this propeller on any 6x4 drone?

No. The 6x4 designation alone does not guarantee compatibility. Check the exact hub, mounting configuration, rotation direction, and your drone or motor specifications before installation.

Is this a CW and CCW pair?

This listing is specified as CW, with 2 pieces supplied. It should not be treated as a CW/CCW pair unless the product packaging or manufacturer specification confirms that configuration.

6040/6040R Drone Propeller – Glass Fiber Nylon, Grey, CW – 2Pc

The 6040/6040R Drone Propeller is a glass fiber nylon propeller designed for compatible drones, multirotors, and RC aircraft. This propeller features a grey finish and CW (clockwise) rotation, making it suitable as a replacement propeller for compatible propulsion systems.

Made from a glass fiber reinforced nylon material, the propeller combines a lightweight construction with improved rigidity compared with standard unreinforced plastic propellers. Its 6040/6040R size designation is intended for compatible motors and drone configurations that use this propeller specification.

Key Features

• 6040/6040R Size: Designed for compatible drone and RC propulsion systems using the 6040 specification.
• Glass Fiber Nylon: Reinforced nylon construction provides a lightweight and rigid propeller structure.
• CW Rotation: Clockwise rotating propeller for compatible motor and frame configurations.
• Grey Colour: Neutral grey finish suitable for replacement and matching drone assemblies.
• 2-Piece Pack: Includes 2 clockwise propellers for convenient replacement.
• Replacement Propeller: Suitable for replacing damaged or worn propellers on compatible drones and RC aircraft.

Product Specifications

Applications

The 6040 drone propeller is suitable for compatible:

• Multirotor drones
• Quadcopters
• FPV and aerial robotics projects
• DIY drones
• RC aircraft
• UAV propulsion systems
• Drone repair and maintenance
• Replacement applications

Glass Fiber Nylon Construction

The glass fiber reinforced nylon construction is designed to provide a balance between weight and rigidity. This makes the 6040 propeller suitable for applications where a lightweight yet durable propeller is required.

Propeller performance depends on the motor, battery, frame, aircraft weight, and overall propulsion configuration. A propeller should only be used when its size, mounting interface, rotation direction, and operating requirements are compatible with the drone.

CW Rotation – Important Compatibility Information

This product is the CW (clockwise) version. Drone propulsion systems commonly use propellers with different rotation directions to generate balanced thrust.

Do not substitute a CW propeller for a CCW propeller unless the drone's motor and propulsion configuration are specifically designed for it. Verify the rotation direction and propeller orientation of the original component before installation.

Why Replace Your Drone Propeller?

Propellers can become damaged due to crashes, contact with obstacles, transportation, or repeated use. Even small cracks, chips, bends, or deformation can affect the balance and performance of a drone.

Replacing a damaged propeller with a compatible 6040/6040R propeller can help restore the intended propulsion configuration. Always inspect the propeller carefully before flight and replace it if there are visible signs of damage.

Installation Information

Switch off the drone and disconnect the battery before replacing the propeller. Install the propeller on the correct motor and confirm that the rotation direction matches the original configuration.

Tighten the propeller securely without applying excessive force. After installation, check that the propeller rotates freely and does not contact the frame, motor, wires, or other components.

Before flight, inspect all propellers for cracks, deformation, or imbalance and perform an appropriate low-power test.

Package Includes

• 2 × 6040/6040R Glass Fiber Nylon Grey CW Drone Propellers

Frequently Asked Questions

What is a 6040 drone propeller?

A 6040 propeller is a specific propeller size used in compatible drone and RC propulsion systems. Compatibility should be checked against the motor and aircraft configuration before use.

What does 6040R mean?

6040R is a designation used for the corresponding propeller variant in this product series. Always compare the original propeller's markings and specifications before ordering.

What does CW mean on a drone propeller?

CW means clockwise rotation. This propeller is designed for a motor configuration that requires a clockwise-rotating propeller.

What material is this propeller made from?

This propeller is made from glass fiber reinforced nylon, providing a lightweight and rigid construction for compatible drone applications.

How many propellers are included?

This listing includes 2 CW propellers.

Can I use this propeller on any drone?

No. Check the propeller size, mounting method, motor compatibility, rotation direction, and overall propulsion requirements before installation.

When should I replace a drone propeller?

Replace the propeller if it has cracks, chips, bends, significant scratches, deformation, or other visible damage. Damaged propellers should not be used for flight.

HP LaserJet 1020 & P1007 Premium Quality Pickup Roller Combo

The HP LaserJet 1020 and P1007 Pickup Roller Combo is a convenient replacement set containing one pickup roller for each compatible printer model. The combo includes 1 pickup roller for HP LaserJet 1020 and 1 pickup roller for HP LaserJet P1007, making it a practical choice for printer technicians, service centres, and users maintaining multiple compatible HP LaserJet printers.

The pickup roller is responsible for gripping and feeding paper from the input tray into the printer's paper path. When a roller becomes worn, smooth, contaminated, or damaged, the printer may experience paper feeding problems, multiple-sheet pickup, or difficulty picking up paper from the tray. Replacing the worn roller can help restore reliable paper feeding when the roller is the source of the problem.

Key Features

• 2-Piece Combo: Includes 1 pickup roller for HP LaserJet 1020 and 1 pickup roller for HP LaserJet P1007.
• Premium Quality Replacement: Suitable for routine printer maintenance and replacement applications.
• Paper Feed Component: Designed to provide the necessary grip for feeding paper from the input tray.
• Two Compatible Models: Convenient combo for servicing compatible HP LaserJet 1020 and P1007 printers.
• Repair-Friendly: Suitable for printer technicians, service centres, and DIY maintenance.
• Easy Replacement: Designed as a replacement component for worn or damaged pickup rollers.

Compatible Printers

This pickup roller combo is intended for the following printer models:

• HP LaserJet 1020 – 1 pickup roller
• HP LaserJet P1007 – 1 pickup roller

Before ordering, verify the exact printer model and compare the original roller with the product specifications and images to confirm compatibility.

Signs of a Worn Pickup Roller

A pickup roller gradually loses its grip as it wears. A worn roller can contribute to paper-feeding problems such as:

• Printer fails to pick up paper from the tray
• Paper feeds intermittently
• Paper feed requires multiple attempts
• Paper slips while entering the printer
• Multiple sheets are picked up together
• Paper jams occur near the pickup area

Paper feed problems can also result from worn separation pads, incorrect paper loading, foreign objects, paper quality, or other printer components. Inspect the complete paper-feed mechanism before replacing the roller.

Why Replace the Pickup Roller?

The pickup roller is a frequently used mechanical component in a laser printer's paper-feed system. Continuous contact with paper gradually affects the roller's surface and its ability to grip the paper effectively.

Replacing a worn roller is often part of routine printer maintenance. This HP 1020 and P1007 pickup roller combo provides two model-specific replacement rollers in a single package, making it useful for maintaining both compatible printers.

Installation Information

Turn off and disconnect the printer from the power supply before beginning the replacement. Remove the existing pickup roller according to the printer's service procedure and install the replacement roller in the correct position.

After installation, inspect the paper path and ensure that the roller rotates freely. Load suitable paper correctly and perform a test print to verify proper paper pickup and feeding.

If the printer continues to experience feeding problems after replacing the roller, inspect the separation pad, paper tray, paper path, gears, and other feed components.

Product Specifications

Package Includes

• 1 × Pickup Roller for HP LaserJet 1020
• 1 × Pickup Roller for HP LaserJet P1007

Frequently Asked Questions

What is included in this HP pickup roller combo?

The package includes 2 pickup rollers: 1 roller for HP LaserJet 1020 and 1 roller for HP LaserJet P1007.

Which printers are compatible with these pickup rollers?

The rollers are intended for the HP LaserJet 1020 and HP LaserJet P1007 respectively. Verify your exact printer model before ordering.

What does a pickup roller do?

The pickup roller grips paper from the input tray and feeds it into the printer's paper path. A worn roller can cause paper pickup and feeding problems.

How do I know if my pickup roller needs replacement?

Common signs include paper not being picked up, intermittent paper feeding, paper slipping, multiple-sheet feeding, and repeated paper-feed issues.

Can I use the HP 1020 roller in the P1007?

Do not interchange the rollers unless compatibility has been specifically confirmed. The combo contains a model-specific replacement roller for each printer.

Is this combo suitable for printer technicians?

Yes. The two-piece set is convenient for printer repair technicians and service centres that maintain compatible HP LaserJet 1020 and P1007 printers.

720 Magnetic Micro Coreless Drone Motor with Fan Blade

The 720 Magnetic Micro Coreless Drone Motor with Fan Blade is a compact brushed coreless motor designed for micro drones, small flying models, DIY aircraft, robotics projects, and other lightweight applications. Its small form factor makes it suitable for projects where low weight and compact motor dimensions are important.

This 720 coreless drone motor comes with a fan blade, providing a convenient motor-and-propeller combination for compatible micro flying projects. The magnetic coreless motor design is commonly used in miniature aircraft and drone applications where a lightweight motor is required for driving a small propeller.

Key Features

• 720 Coreless Motor: Compact micro motor designed for lightweight electronic and flying applications.
• Magnetic Motor Design: Designed for efficient operation in suitable miniature motor applications.
• Fan Blade Included: Supplied with a compatible fan blade for convenient use in suitable projects.
• Lightweight Construction: Suitable for applications where minimizing overall system weight is important.
• Compact Size: Designed for micro drones, small aircraft, robotics, and DIY projects.
• Replacement Motor: Useful for replacing a damaged or worn motor in a compatible micro drone or model.

Applications

The 720 micro coreless motor can be used in various lightweight applications, including:

• Micro and mini drones
• Small quadcopters and flying models
• DIY RC aircraft
• Miniature robotics projects
• Educational electronics projects
• Small fan and propeller mechanisms
• DIY aerial robotics
• Replacement applications for compatible micro motors

Why Choose a 720 Coreless Motor?

Micro drones and lightweight flying models require motors that can provide suitable propulsion without adding unnecessary weight. A 720 coreless motor offers a compact solution for miniature applications where space and weight are limited.

The included fan blade makes this product convenient for projects that require a motor and propeller combination. It can also be useful as a replacement component when servicing a compatible micro drone or small flying model.

Replacement & Compatibility

Before using this motor as a replacement, compare the original motor's physical dimensions, shaft arrangement, wire configuration, operating voltage, rotation direction, and fan-blade size with the replacement.

Motor performance depends on the battery, propeller, frame, wiring, and electronic components used in the complete system. Do not select a replacement motor based on the model number alone.

Installation Information

Disconnect the battery before replacing or installing the motor. Connect the motor wires according to the original configuration and make sure the motor is securely mounted.

Check that the fan blade is firmly attached and can rotate freely without contacting the frame or other components. After installation, perform an initial test at low power and inspect the motor for abnormal vibration, noise, or excessive heating.

Product Specifications

Package Includes

• 1 × 720 Magnetic Micro Coreless Drone Motor
• 1 × Fan Blade

Frequently Asked Questions

What is a 720 coreless drone motor?

A 720 coreless drone motor is a compact brushed motor designed for miniature applications such as micro drones, small aircraft, and lightweight DIY projects.

Does this motor include a fan blade?

Yes. This product is supplied with a fan blade as specified in the product listing.

Where can I use the 720 micro motor?

It can be used in compatible micro drones, small quadcopters, RC aircraft, miniature robotics, DIY flying models, and other lightweight mechanical projects.

Can I use this as a replacement drone motor?

Yes, provided the motor's dimensions, voltage, wiring, shaft configuration, rotation direction, and fan-blade specifications match the original motor and the requirements of your drone.

Is the 720 motor suitable for all micro drones?

No. Micro drone motors are not universally interchangeable. Check the electrical and mechanical specifications of your existing motor before purchasing a replacement.

What should I check before installing the motor?

Check the motor voltage, dimensions, wire configuration, shaft and fan-blade compatibility, mounting arrangement, and required rotation direction before installation.

RG316 SMA Male to Male Extension Cable – 10cm (100mm)

The RG316 SMA Male to Male Extension Cable is a compact RF extension cable designed to connect two devices or components equipped with compatible SMA female interfaces. With a length of 10cm (100mm), it provides a convenient way to extend an existing SMA connection while keeping the overall installation compact and organized.

Built around RG316 coaxial cable and fitted with SMA male connectors on both ends, this extension cable is suitable for a variety of RF, antenna, wireless communication, GPS, networking, testing, and electronic applications. Its short length makes it particularly useful where only a small amount of additional cable is required.

Key Features

• 10cm / 100mm Length: Compact cable length for short-distance RF connections and extensions.
• SMA Male to Male: Features an SMA male connector at both ends for connecting compatible SMA female ports.
• RG316 Coaxial Cable: Uses RG316-style coaxial construction for RF signal connections.
• Compact Design: Suitable for installations where space and cable management are important.
• Easy RF Extension: Allows an existing SMA connection to be extended without replacing the complete cable assembly.
• Versatile Application: Suitable for compatible antenna, wireless, GPS, RF testing, and electronic equipment.

Product Specifications

Applications

The RG316 SMA extension cable can be used in a wide range of compatible RF and electronic systems, including:

• RF and antenna connections
• Wireless communication equipment
• GPS and navigation systems
• Wi-Fi and networking equipment
• RF modules and electronic devices
• Signal testing and measurement setups
• Laboratory and DIY electronics projects
• Radio communication equipment

Why Use an SMA Male to Male Extension Cable?

Replacing an entire RF cable is not always necessary when additional cable length is required. A short SMA male to male extension cable provides a convenient connection between compatible SMA female ports while maintaining a compact installation.

The 10cm length is useful for setups where a longer extension would create unnecessary cable loops or clutter. It can also make component positioning easier when RF modules, antennas, adapters, or other equipment need to be separated by a short distance.

Compatibility

This cable is designed for equipment featuring compatible SMA female interfaces on both connection points. Before ordering, verify the connector gender and interface type of your equipment.

Important: SMA and RP-SMA connectors are different. An SMA male connector should not be assumed to be compatible with an RP-SMA female connector. Check the connector specification of your equipment before purchasing.

Installation Information

Connect each SMA male end to a compatible SMA female port and tighten the connector appropriately by hand or with a suitable connector tool. Avoid excessive force, sharp bends, or unnecessary stress on the cable and connectors.

For RF applications, keep the cable routing clean and avoid placing unnecessary mechanical stress on the connectors. Always verify the frequency and electrical requirements of your application before use.

Package Includes

• 1 × RG316 SMA Male to Male Extension Cable – 10cm (100mm)

Frequently Asked Questions

What is an RG316 SMA Male to Male cable?

It is an RF coaxial extension cable using RG316-style cable with an SMA male connector fitted to each end. It is designed to connect compatible SMA female interfaces.

What is the length of this SMA extension cable?

The cable length is 10cm (100mm).

What is the connector type?

This cable has SMA male connectors on both ends, making it an SMA male-to-male extension cable.

Where can I use this RG316 SMA cable?

It can be used in compatible RF, antenna, wireless communication, GPS, networking, testing, radio, and electronics applications.

Can I use this cable with RP-SMA connectors?

Not necessarily. SMA and RP-SMA use different connector configurations. Verify the exact connector type and gender of your equipment before purchasing.

Is this cable suitable for RF applications?

Yes. RG316 coaxial cable with SMA connectors is commonly used for RF signal connections. However, the cable should be selected according to the frequency, power, impedance, and other requirements of the specific application.

What is the benefit of the 10cm cable length?

The 10cm length provides a short and compact extension where only limited additional distance is required between two compatible SMA connections.

CCD Scanner Cable for Epson L3310 Printer

The CCD Scanner Cable for Epson L3310 is a replacement cable designed to provide the electrical connection between the scanner assembly and the internal electronics of a compatible Epson L3310 printer. It is suitable for printer repair and maintenance when the original scanner cable is damaged, worn, disconnected, or identified as the cause of scanner communication problems.

The scanner cable plays an important role in transferring electrical signals between the scanner assembly and the printer's main electronics. A damaged or incorrectly connected cable can affect scanning operation and may result in scanner-related errors. Replacing a faulty cable with a compatible replacement can help restore normal scanner communication.

Key Features

• Designed for Epson L3310: Suitable for compatible Epson L3310 printer and scanner assemblies.
• CCD Scanner Connection: Designed to connect the scanner assembly with the printer's internal electronics.
• Replacement Cable: Useful for replacing a damaged or faulty original scanner cable.
• Printer Repair Component: Suitable for technicians, service centres, and printer maintenance.
• Internal Cable Design: Designed for routing within the printer's scanner assembly.

Compatible Printer

This Epson L3310 scanner cable is intended for:

• Epson L3310 Printer

Before purchasing, compare the original cable's connector type, number of contacts, cable length, orientation, and physical configuration with the replacement to confirm compatibility.

When Should You Replace the CCD Scanner Cable?

A scanner cable may require replacement if it has visible physical damage or if diagnostic testing indicates a connection problem between the scanner assembly and the printer electronics. Possible symptoms include:

• Scanner not responding
• Scanner communication errors
• Intermittent scanning operation
• Visible damage or creasing on the cable
• Damaged or loose connectors
• Scanner problems after printer disassembly or repair

Scanner failures can also be caused by the scanner assembly, mainboard, connectors, sensors, or other internal components. Proper diagnosis should be performed before replacing the cable.

Applications

The L3310 CCD scanner cable is intended for repair and maintenance of compatible Epson L3310 printer scanner assemblies. It can be useful for printer technicians, repair centres, and users replacing damaged internal scanner wiring.

Installation Information

Disconnect the printer from the power supply before opening the device or accessing internal components. Carefully remove the existing scanner cable while noting its original routing and connector orientation.

Install the replacement cable in the correct orientation and ensure that all connectors are fully seated. Avoid excessive bending, twisting, pulling, or pinching of the cable during installation.

Because incorrect cable orientation or an improperly seated connector can cause malfunction, installation should preferably be performed by a qualified printer technician.

Product Specifications

Package Includes

• 1 × CCD Scanner Cable for Epson L3310

Frequently Asked Questions

Which printer is this CCD scanner cable compatible with?

This cable is intended for the Epson L3310 printer. Compare the original cable configuration before ordering.

What is the function of the CCD scanner cable?

The cable provides the electrical connection required for communication between the scanner assembly and the printer's internal electronics.

Can a damaged scanner cable cause scanning problems?

Yes. A damaged or improperly connected cable can interfere with scanner communication. However, scanner errors can also originate from the scanner assembly, connectors, mainboard, or other internal components.

When should I replace the Epson L3310 scanner cable?

Replacement may be appropriate when the cable has visible damage or has been identified through troubleshooting as the cause of a scanner connection or communication issue.

Can I install this cable myself?

The cable is installed inside the printer and requires access to internal components. Professional installation is recommended if you are unfamiliar with printer disassembly and ribbon-cable connections.

How can I verify compatibility?

Check the printer model and compare the replacement cable with your original cable, including its connector arrangement, contact count, length, orientation, and physical design.

Control Panel Cable for Epson L3310 Printer

The Epson L3310 Control Panel Cable is a replacement cable designed for connecting the control panel to the corresponding electronics inside a compatible Epson L3310 printer. It is suitable for printer repair and maintenance when the original control panel cable is damaged, worn, disconnected, or suspected to be causing communication problems between the panel and the printer's main electronics.

The control panel cable carries electrical signals between the printer's control interface and internal circuitry. A properly installed replacement cable can help restore communication and normal control-panel operation when the original cable has been identified as faulty.

Key Features

• Compatible with Epson L3310: Designed for use with compatible Epson L3310 printers.
• Control Panel Connection: Connects the printer control panel with the corresponding internal electronics.
• Replacement Component: Suitable for replacing a damaged or faulty original cable.
• Printer Repair Part: Useful for technicians, service centres, and printer repair applications.
• Compact Cable Design: Suitable for internal printer installation and cable routing.

Compatible Printer

This Epson L3310 panel cable is intended for:

• Epson L3310 Printer

Before ordering, compare the existing cable with the product images and verify the connector arrangement, contact count, cable length, and orientation to ensure compatibility.

When Should the Control Panel Cable Be Replaced?

A control panel cable may need replacement if it has been physically damaged or if testing indicates that the cable is interrupting communication between the control panel and printer electronics. Possible symptoms can include:

• Control panel buttons not responding correctly
• Intermittent control panel operation
• Printer control interface communication issues
• Visible damage to the cable or connectors
• Loose or damaged cable connections
• Problems following printer disassembly or repair

These symptoms may also be caused by the control panel, mainboard, connectors, or other internal components. Proper diagnosis is recommended before replacing the cable.

Installation Information

Disconnect the Epson L3310 from the power supply before opening the printer or working with internal cables. Carefully remove the existing cable and note its original routing and connector orientation.

Install the replacement L3310 control panel cable in the same orientation and ensure that both connectors are completely seated. Avoid excessive bending, twisting, pulling, or pinching during installation.

Because incorrect cable orientation can cause malfunction or potentially damage electronic components, installation should preferably be performed by a qualified printer technician.

Product Specifications

Package Includes

• 1 × Control Panel Cable for Epson L3310

Frequently Asked Questions

Which printer is this control panel cable compatible with?

This replacement cable is intended for the Epson L3310 printer. Verify the physical configuration of your original cable before ordering.

What is the function of the Epson L3310 control panel cable?

The cable provides the electrical connection between the printer's control panel and the corresponding internal electronics.

Can a faulty cable cause control panel problems?

Yes. A damaged, loose, or improperly connected cable can interfere with communication between the control panel and the printer's electronics. However, the panel, connectors, or mainboard can also cause similar symptoms.

Is this an original Epson cable?

Product originality should be confirmed from the specific listing and supplier documentation. Do not assume OEM status solely from model compatibility.

Can I replace the cable myself?

The cable is installed inside the printer and requires access to internal components. Professional installation is recommended if you are not familiar with printer disassembly and electronic connectors.

How should I check compatibility?

Verify that your printer is an Epson L3310 and compare the replacement cable's connectors, orientation, length, and physical arrangement with your existing cable before purchasing.

Head Cable + Sensor Cable Folded With Clip for Epson L3310 Printer

The Head Cable + Sensor Cable with Clip for Epson L3310 is a replacement cable assembly designed for servicing and repairing compatible Epson L3310 printers. The set combines the head cable and sensor cable in a folded configuration with a clip, providing a practical replacement for damaged, worn, or faulty cable assemblies.

Flexible ribbon and sensor cables are important for transferring electrical signals between the printer's control electronics, printhead, and sensors. Damage, improper folding, broken conductors, or loose connections can result in printing errors, sensor-related problems, or communication issues. Replacing a faulty cable with a compatible assembly can help restore proper printer operation.

Key Features

• Compatible with Epson L3310: Designed as a replacement cable assembly for the Epson L3310 printer.
• Combined Cable Set: Includes both the head cable and sensor cable.
• Folded Configuration: Supplied in a folded arrangement suitable for the intended printer installation.
• Integrated Clip: Includes a clip for keeping the cable assembly organized and properly positioned.
• Replacement Part: Suitable for printer repair, maintenance, and replacement of damaged cables.
• Flexible Flat Cable: Designed to provide electrical signal and connection between compatible printer components.

Compatible Printer

This cable assembly is intended for:

• Epson L3310 Printer

Always compare the original cable's connector arrangement, number of contacts, length, orientation, and physical configuration before ordering to ensure compatibility.

When Should You Replace the Cable?

A printer cable may require replacement when it has visible physical damage or when a technician has identified it as the cause of a connection or communication problem. Common signs can include:

• Printhead communication errors
• Intermittent printer operation
• Sensor-related errors
• Visible cracks, cuts, or damaged conductors
• Loose or damaged cable connectors
• Problems occurring after printer disassembly or repair

These symptoms can also be caused by other printer components. Inspect the connectors, printhead, sensors, motherboard, and related wiring before replacing the cable.

Applications

The Epson L3310 head and sensor cable is intended for printer servicing and repair. It can be useful for technicians, printer repair centres, and users replacing damaged internal cable assemblies in compatible Epson L3310 units.

Installation Information

Switch off and disconnect the printer from the power supply before accessing internal components. Carefully remove the existing cable and compare its routing and connector orientation with the replacement.

Install the replacement cable in the correct orientation and secure it using the supplied clip. Make sure all connectors are fully seated and that the cable is not sharply bent, pinched, or incorrectly routed.

Because ribbon cables and printer connectors can be sensitive to incorrect orientation, installation should preferably be performed by a qualified printer technician.

Product Specifications

Package Includes

• 1 × Head Cable (Folded)
• 1 × Sensor Cable
• 1 × Cable Clip

Frequently Asked Questions

Which printer is this cable compatible with?

This cable assembly is listed for the Epson L3310 printer. Check the original cable and connector configuration before purchasing.

What does this cable set include?

The set includes a folded head cable, sensor cable, and clip as shown in the product listing.

Why would an Epson L3310 need a replacement head cable?

A damaged or improperly connected head cable can interfere with communication between the printer electronics and printhead. Replacing a faulty cable may resolve problems when the cable has been identified as the cause.

Does the cable come with a clip?

Yes. This product is supplied with the clip used to hold the cable assembly in its intended position.

Can I install the cable myself?

Installation involves accessing internal printer components and correctly routing and connecting ribbon cables. If you are unfamiliar with printer repair, professional installation is recommended.

Should I verify compatibility before ordering?

Yes. Compare your existing cable with the product images and verify the printer model, connector type, cable arrangement, and orientation before placing an order.

On/Off Switch for HP LaserJet M1136, M1213NF & M1217 Printer

The On/Off Switch for HP LaserJet M1136, M1213NF and M1217 printers is a replacement power switch designed to help restore normal power control on compatible HP LaserJet multifunction printers. It is a practical replacement option when the original switch becomes damaged, loose, unresponsive, or fails to turn the printer on or off correctly.

A faulty power switch can make a printer difficult or impossible to operate, even when the printer's internal power supply and other components are functioning correctly. Replacing the damaged switch can help restore convenient power control without replacing the complete printer assembly.

Key Features

• Compatible Replacement: Designed for use with compatible HP LaserJet printer models.
• Multiple Model Compatibility: Suitable for HP LaserJet M1136, M1213NF and M1217 printer variants.
• On/Off Power Control: Provides the physical switching function required to control printer power.
• Repair-Friendly Solution: Useful when the original printer power switch is damaged or no longer functioning properly.
• Compact Printer Component: Designed as a replacement component for the printer's existing switch assembly.
• Suitable for Printer Repair: A practical option for technicians, repair professionals and printer service centres.

Compatible HP LaserJet Printers

• HP LaserJet Pro M1136 Multifunction Printer
• HP LaserJet Pro M1213NF Multifunction Printer
• HP LaserJet Pro M1217 Multifunction Printer

Important: Please verify your printer's exact model and compare the original switch, connector and physical configuration before ordering.

When Should You Replace the Printer On/Off Switch?

A damaged or worn power switch may cause intermittent power control or prevent the printer from responding when the switch is pressed. Common indications of a faulty switch can include:

• Printer does not respond when the power switch is pressed
• Power switch feels loose or physically damaged
• Intermittent power operation
• Switch does not maintain proper contact
• Printer turns off unexpectedly when the switch is disturbed

Before replacing the switch, technicians should also check the printer's power cable, power supply, connectors and other relevant electrical components to ensure that the switch is the actual cause of the problem.

Applications

This HP LaserJet power switch is intended for printer repair and maintenance applications. It can be useful for service technicians and repair centres working on compatible HP LaserJet multifunction printers.

The replacement can help restore the physical power-control function without unnecessarily replacing larger printer assemblies when the fault is isolated to the On/Off switch.

Installation Information

Installation should be performed by a qualified printer technician or someone familiar with electronic equipment repair. Disconnect the printer from the mains power supply before opening the device or working on internal components.

During installation, compare the replacement switch with the original component and confirm the connector, mounting arrangement and electrical configuration. After installation, inspect all connections carefully before reconnecting the printer to the power supply.

Product Specifications

Why Choose This Replacement Switch?

Replacing a defective power switch can be a more practical repair than replacing an entire printer assembly. This component is intended for compatible HP LaserJet models and can help technicians address physical switch-related failures during printer servicing.

For the best results, confirm the exact printer model and switch configuration before purchasing. Compatibility should be checked against the original component rather than relying only on the printer series name.

Package Includes

• 1 × On/Off Switch for compatible HP LaserJet Printer

Frequently Asked Questions

Which printers are compatible with this On/Off Switch?

This replacement switch is listed for HP LaserJet M1136, M1213NF and M1217 printer models. Verify your exact model and the physical configuration of the original switch before ordering.

What does the HP LaserJet On/Off Switch do?

The switch provides the physical power-control function used to turn a compatible printer on or off.

Can this switch fix a printer that does not turn on?

It may resolve the problem if the failure is caused by a defective physical power switch. However, a printer that does not power on can also have faults in its cable, power supply or internal electronics.

Is this suitable for printer repair technicians?

Yes. The switch is intended as a replacement component for servicing compatible HP LaserJet printers and can be useful for printer technicians and repair centres.

Should I check compatibility before ordering?

Yes. Compare your printer's exact model, original switch and connector configuration with the replacement component before placing an order.

Hobbywing XRotor 40A ESC Wire Leaded Speed Controller

The Hobbywing XRotor 40A ESC is a brushless electronic speed controller designed for compatible drone, multirotor, and RC applications. This wire-leaded ESC provides a practical solution for replacing a damaged speed controller or servicing an existing power system where a compatible 40A ESC is required.

Designed to control the speed and direction of a compatible brushless motor, the Hobbywing XRotor 40A ESC helps provide responsive motor control and reliable operation when correctly matched with the motor, battery, propeller, and flight-control system. The wire-leaded configuration also makes it convenient for installation and replacement in compatible assemblies.

Key Features

• 40A Rated ESC: Designed for applications requiring a compatible 40A electronic speed controller.
• Hobbywing XRotor Series: Genuine XRotor-series speed controller for compatible drone and RC systems.
• Wire-Leaded Design: Supplied with wire leads for convenient electrical connection and installation.
• Brushless Motor Control: Designed to regulate power supplied to compatible brushless motors.
• Drone & RC Applications: Suitable for compatible multirotor, UAV, and RC power systems.
• Replacement Solution: Useful for repairing or replacing a faulty or damaged ESC in a compatible setup.

Applications

The Hobbywing XRotor 40A ESC can be used in compatible:

• Multirotor drones and quadcopters
• UAV and aerial robotics projects
• RC aircraft and other RC models
• Brushless motor systems
• Drone repair and replacement applications
• DIY electronics and robotics projects

Why Choose the Hobbywing XRotor 40A ESC?

A properly matched ESC is essential for reliable brushless motor operation. The ESC manages the electrical power delivered to the motor according to the control signal received from the flight controller, receiver, or other compatible control system.

The XRotor 40A ESC is a suitable replacement option when your existing system requires a compatible Hobbywing XRotor speed controller. Its wire-leaded configuration can simplify replacement work where the original ESC uses a similar wiring arrangement.

Before installation, verify the exact ESC model, battery voltage, motor specifications, connector arrangement, wiring, and flight-controller compatibility. Do not select an ESC based on current rating alone.

Installation & Compatibility

Before connecting the ESC, switch off the battery and inspect all wiring and connectors. Confirm the polarity of the power connection and ensure that the ESC is compatible with the motor and control system.

When replacing an existing ESC, compare the original unit's model number, wire configuration, connectors, mounting arrangement, and electrical specifications with the replacement. Secure all connections properly before powering the system.

For drone and RC applications, the ESC should be selected according to the complete power-system requirements, including motor current, battery voltage, propeller configuration, and operating conditions.

Package Includes

• 1 × Hobbywing XRotor 40A ESC Wire Leaded Speed Controller

Frequently Asked Questions

What is the Hobbywing XRotor 40A ESC?

The Hobbywing XRotor 40A ESC is an electronic speed controller designed to control compatible brushless motors in drone, multirotor, UAV, and RC applications.

What does a 40A ESC do?

An ESC regulates the electrical power supplied to a brushless motor, allowing the flight controller or other control system to control motor speed.

Can this ESC be used as a replacement?

Yes, it can be used as a replacement when its model, electrical specifications, wiring, connectors, and control protocol are compatible with the original ESC and the rest of the power system.

Is this ESC suitable for drones?

The XRotor series is designed for aerial and multirotor applications. However, compatibility should be verified for the specific drone, motor, battery, and flight-control system before installation.

Does the product include wire leads?

Yes. This listing is for the wire-leaded version of the Hobbywing XRotor 40A ESC. Please check the product images and package details for the exact wire and connector configuration.

How do I choose the correct ESC for my motor?

Check the motor's maximum current, battery voltage, propeller combination, control protocol, and other system requirements. The ESC's continuous and peak current capabilities should be appropriate for the complete power system.

Amass AS150U-M Male Connector Original – High-Current Power & Signal Connector

The Amass AS150U-M Male Connector is a high-current power and signal connector designed for demanding electrical applications such as UAVs, VTOL aircraft, lithium battery systems, motor controllers, and other industrial electronics. Its 6-pin configuration combines 2 power contacts and 4 signal contacts, allowing power and signal connections to be integrated into a single connector housing.

Designed for reliable electrical connections, the AS150U-M features copper contacts with gold-flash plating and a polyamide housing. Its straight cable-mount design is suitable for soldered connections in compatible power systems. The connector is particularly useful where a secure, compact, and high-current connection is required.

Key Features

• Original Amass Connector: Genuine AS150U-M male connector for compatible AS150U-series applications.
• Combined Power & Signal Connection: Includes 2 main power contacts and 4 signal contacts in one connector.
• High-Current Capability: Designed for high-current power applications, with a manufacturer-rated current of 70A under specified conditions.
• Gold-Flash Plated Contacts: Copper contacts with gold-flash plating help provide reliable electrical conductivity.
• Secure Cable-Mount Design: Suitable for soldered cable connections in compatible electrical systems.
• Durable Housing: Polyamide body with UL94V-0 flammability rating according to the listed specification.
• Wide Operating Temperature: Suitable for applications within the specified -20°C to +120°C operating range.

Technical Specifications

Applications

The AS150U-M male connector is suitable for a variety of high-current power and signal applications, including:

• UAV and VTOL aircraft
• FPV drone and aerial robotics power systems
• LiPo battery connections
• Motor controllers and ESC systems
• Battery charging and power distribution systems
• Industrial electronics and automation equipment
• DIY high-current electrical projects

Why Choose the Amass AS150U-M?

The Amass AS150U-M is designed for applications where both power delivery and signal connections are required in a compact connector. Its integrated 6-pin configuration helps simplify wiring while maintaining a secure connection between compatible components.

For UAV and VTOL systems, the connector can be useful for connecting battery and controller assemblies where high-current power and additional signal connections are required. Before installation, verify the connector series, polarity, pin configuration, cable size, and electrical requirements of your specific application.

Installation Information

The AS150U-M is a cable-mount connector designed for soldered electrical connections. Ensure the connector is correctly oriented and securely soldered before connecting it to a power source.

Always inspect the solder joints, confirm polarity, and verify the current and voltage requirements of the connected system. Do not exceed the connector's specified electrical limits.

Package Includes

• 1 × Amass AS150U-M Male Connector Original

Frequently Asked Questions

What is the Amass AS150U-M?

The Amass AS150U-M is a male AS150U-series connector designed for high-current power and signal connections. It features 2 power contacts and 4 signal contacts in a 6-pin configuration.

What is the current rating of the AS150U-M?

The listed manufacturer specification gives a rated current of 70A under specified conditions. Always consider the actual cable size, temperature, installation, and application requirements before selecting a connector.

Where can the AS150U-M be used?

The connector is suitable for compatible UAV, VTOL, LiPo battery, motor controller, and industrial electronics applications requiring high-current power and signal connections.

Is the AS150U-M a male connector?

Yes. The AS150U-M is the male version of the AS150U connector series.

Does the AS150U-M have signal pins?

Yes. The connector includes 4 signal contacts in addition to its 2 main power contacts.

Is this connector supplied with wires?

This listing is for the connector itself. Wires are not included unless specifically mentioned in the product package details.

Keep your printer’s paper-handling system running smoothly with this Pickup Duplex Gear, designed for compatible HP LaserJet Pro and Color LaserJet Pro MFP models. This replacement gear helps support the proper operation of the duplex/paper pickup mechanism, ensuring consistent paper movement during printing and two-sided print jobs.

Key Features

• Compatible Replacement: Designed for selected HP LaserJet Pro and Color LaserJet Pro MFP models.
• Reliable Paper Handling: Helps maintain smooth and consistent paper pickup and feeding.
• Duplex Function Support: Suitable for printers using the compatible duplex paper-handling mechanism.
• Quality Construction: Made for dependable performance and long-term use.
• Cost-Effective Repair: Replace the worn or damaged gear instead of replacing the complete assembly.

Compatible Printer Models

• HP LaserJet Pro MFP M329
• HP LaserJet Pro MFP M426
• HP LaserJet Pro MFP M427
• HP LaserJet Pro MFP M428
• HP LaserJet Pro MFP M429
• HP LaserJet Pro MFP 4104
• HP Color LaserJet Pro MFP M377
• HP Color LaserJet Pro MFP M477
• HP Color LaserJet Pro MFP M479

Ideal Replacement for

This gear is suitable when the original duplex or pickup gear is worn, damaged, cracked, slipping, or causing paper-feeding problems. Replacing the faulty gear can help restore the printer’s paper-handling performance without replacing the entire mechanism.

The MC-G06 Ink Maintenance Box is a replacement waste ink maintenance unit designed for compatible Canon PIXMA printers. It collects excess ink generated during printhead cleaning, ink flushing, and other maintenance operations, helping prevent ink leakage and maintain smooth printer performance.

This maintenance box is suitable for Canon PIXMA TS7720, TR7820, TS76401, TS77401, TS7650i, TS7750i, TS7770A, TS7770, TS7780A, TS7780, and TS7790A series printers. It is an ideal replacement when the existing maintenance box is full or the printer displays a maintenance box replacement warning.

Key Features

• Replacement MC-G06 Ink Maintenance Box

• Designed to collect waste ink from printer maintenance operations

• Helps prevent waste ink overflow and leakage

• Easy to install and replace

• Suitable for compatible Canon PIXMA printer models

• Ideal for maintaining reliable printer operation

Compatible Printer Models

Canon PIXMA TS7720, TR7820, TS76401, TS77401, TS7650i, TS7750i, TS7770A, TS7770, TS7780A, TS7780, and TS7790A.

Note: Please verify your printer model and the maintenance box model number before placing an order.

The PF Motor (Paper Feed Motor) is an essential printer component responsible for driving the paper feeding mechanism and ensuring smooth, consistent paper movement through the printer. A faulty PF motor can result in paper feeding problems, paper jams, irregular paper movement, or printing interruptions.

This replacement PF Motor is designed for use with selected Canon Pixma G-Series ink tank printers and is suitable for printer repair, maintenance, and replacement applications.

Compatible Printer Models

• Canon Pixma G2000
• Canon Pixma G2010
• Canon Pixma G3000
• Canon Pixma G3010
• Canon Pixma G4010

Key Features

• Replacement motor for the paper feed mechanism
• Helps ensure smooth and consistent paper feeding
• Suitable for repairing paper feed-related motor issues
• Compatible with selected Canon Pixma G-Series printers
• Ideal for printer technicians, repair centers, and DIY maintenance

Note: Please verify your printer model and compare the original motor before purchasing to ensure proper compatibility.

The Carriage Motor is a replacement printer component responsible for driving the printhead carriage assembly smoothly across the paper during printing. A faulty or worn-out carriage motor can cause carriage movement issues, unusual noise, paper alignment problems, or printing interruptions.

This replacement carriage motor is designed for compatibility with selected Canon Pixma G-Series ink tank printers, making it suitable for repairing printers where the original motor is damaged or no longer functioning properly.

Compatible Printer Models

• Canon Pixma G2000
• Canon Pixma G2010
• Canon Pixma G3000
• Canon Pixma G3010
• Canon Pixma G4010

Key Features

• Replacement motor for the printer carriage mechanism
• Helps restore smooth and consistent carriage movement
• Suitable for printer repair and maintenance
• Designed for compatible Canon Pixma G-Series models
• Ideal replacement for a damaged or malfunctioning carriage motor

Note: Please verify your printer model and compare the original motor before ordering to ensure compatibility.

Keep your Epson EcoTank printer running smoothly with the C9398 Maintenance Box, designed to collect waste ink generated during printer cleaning and maintenance cycles. A properly functioning maintenance box helps prevent ink overflow and supports reliable printer operation.

Compatible Printer Models:

• Epson L1350
• Epson L3310
• Epson L3350
• Epson L5390

Key Features:

• Designed for Epson EcoTank printers
• Helps collect waste ink efficiently
• Supports smooth printer maintenance and operation
• Easy to install and replace
• Ideal replacement for a full or worn-out maintenance box

Product: C9398 Maintenance Box
Compatibility: Epson L1350, L3310, L3350, L5390

Note: Please verify your printer model and maintenance box part number before ordering to ensure compatibility.

The Refill Ink T664 set is designed specifically for Epson printers, including models L110, L210, L310, L405, L455, L550, and L605. This high-quality ink refill kit provides vibrant CMYK colors, ensuring sharp and clear prints for both documents and photos. Ideal for continuous ink supply systems, it supports a wide range of printing needs, from home use to small office environments, maintaining consistent performance and color accuracy.

• Compatible with multiple Epson printer models for hassle-free refilling and extended printer life
• Includes cyan, magenta, yellow, and black inks to deliver full-color print capability
• Formulated for vibrant color output that enhances photo and document quality
• Designed for continuous ink supply systems, reducing the frequency of cartridge replacements
• Easy to use refill bottles minimize mess and ensure precise ink application
• Supports high-volume printing suited for busy home offices and small businesses
• Maintains consistent ink flow to prevent streaks and smudging during printing

The Refill Ink GI-71 is designed for use with Canon G1020, G2020, G2021, G3020, and G3021 printers, delivering high-quality colors for everyday printing needs. This CMYK ink set offers reliable compatibility with these Canon models, making it ideal for both home and office environments. Its smooth flow ensures consistent print output, preserving sharp text and vivid images for various documents and photo projects.

• Includes cyan, magenta, yellow, and black ink tanks for full-color printing versatility
• Formulated to maintain the longevity and performance of compatible Canon printers
• Provides vibrant, true-to-life colors suitable for photos and professional documents
• Easy to refill design reduces downtime and keeps your printer running smoothly
• Compatible specifically with Canon G1020, G2020, G2021, G3020, and G3021 models
• Ensures smudge-resistant prints with consistent ink flow across pages
• Cost-effective solution for frequent printing without sacrificing quality